Seven commonly used sewing methods for processing

0 Comments

Seven commonly used sewing methods for processing

Z

边处理常用的7种缝制方法精讲

General home sewing machines will have more or less needle. The knob needs to be adjusted, and the Z -character needle is the most basic one. People who are mainly used to make up for no sewing machine can also do simple edge anti -silk treatment. But the protection effect is naturally not very ideal, but there is always better than no.

边处理常用的7种缝制方法精讲

If the Z -shaped car seam is performed on a piece of fabric, the sewing of the sewing process will cause the cloth to shrink the fabric. Therefore, sewing thin fabrics or soft fabrics need to be seams of Z -shaped car seams in some positions in the fabric, and then cut off the excess seams. Therefore, when the net version is cut and sew, this excess must be added.

The thick and better fabric can be performed directly on the side of the cloth.

边处理常用的7种缝制方法精讲

Of course, the sequence of sewing and edging is also possible. But there may be some problems. But if you miss it before, you don’t need to remove it, and it will not be a big deal after the seam.

边处理常用的7种缝制方法精讲

The following is the split effect of the seam of the Z -shaped car.

边处理常用的7种缝制方法精讲

The situation of sewing is not required to perform Z -shaped seams. Two pieces can be sutured first and then handled together. Because it is handled two pieces together, there is no problem with too thin fabrics, so the Z -shaped carts can be performed directly on the sewing edge.

边处理常用的7种缝制方法精讲

The first process of processing and sewing is first of all sewing. Just before the stitching processing, I repeatedly emphasized. The seams on the front fabric are on both sides of the seam on the horizontal line, so to a certain extent, two pieces can be covered in two pieces to a certain extent. The gap between the between looks flat. Falling on the side will lead to the front seams, thereby appear a sense of layering. Of course, this refers to a thicker fabric, and the thin cloth is not obvious, so this factor is not considered. From an industrial perspective, it is savored by the perspective of industrial perspective, whether from the ironing perspective, or from the perspective of the seam (the split is separated, and the pour can be wrapped together). In particular, the four -line seam machine is directly connected to the seam, which is more efficient. So if it is not deliberately sophisticated, it is generally one side. The thin cloth will make the sewing thread bear more tear because the sewing thread is split, so the inverted side is the most suitable way to deal with it. As shown in this lesson, splitting sewing and falling to one side corresponds to two different processing sequences. Under normal circumstances, there are Lizi clothes, we do not handle it, I have said this before. For trousers, we must first sew the tailored cloth, and then sew. Leisure clothes, shirts and other thin materials all fall to one side, and it is behind the net.

边处理常用的7种缝制方法精讲

Lock

The role of the lock edge and the z -shaped seam is the same. The difference is that the lock edge needs to be done by the seam machine, and the three lines need to be set to form the protection of the cloth edge. Since it is a three -line line, it is the function that the sewing machine is not available. There are currently no sewing machines, and friends who do not intend to buy the sewing machine, please ignore this moment. Especially the so -called two -line locks of the sewing machine, the three -line locks are broken to the children with the collapse of the wisdom. I won’t tell you how a cool word is compared with the sewing machine.

First of all, the seam machine has a adjustable small cutter, which is used to trim the hair edge before the lock. Of course, although this is very clever, it is not a high -tech, so when the hand disabled party is unstable, do not greedy the refreshing characters I said before. Secondly, there must be a small tail before and after the car seam. Then processed as shown above, there will be no situation of opening. The rest is the same as the Z -shaped seam. It is divided into two cases: splitting seams (first locks) and sutures.

边处理常用的7种缝制方法精讲

The sewing machine is divided into a three -wire seam machine, and the four -line seam machine. The five -line sewing machine is called the tshirt bottom (see two parallel sewing lines of the TSHIRT bottom). Here is the reason why the four -line line is more than the third line is that in addition to locking, another line plays a role in suture. Therefore, if the four -line is all on, the two films are locked together, and they will be sewed with sewing and sew together.

边处理常用的7种缝制方法精讲

Although the distance can be fine -tuned, the sewing portions are still small. Therefore, the average shuttle fabric still uses this step of sewing machine. However, for knitted fabrics, especially elastic fabrics, it is necessary to use this method. Because sewing machines have no way for this fabric. Of course, the sewing machine is also divided into home and industry. However, the difference between the difference between the home and industry without sewing machines.

Edge

边处理常用的7种缝制方法精讲

There is nothing to say along the side of the side. It is a routine with Z -character and bags, but the effect of the flat seam is afraid that even the effect of the z -shaped needle is worse, but the words are always stronger than no. The method is shown in the figure.

边处理常用的7种缝制方法精讲

Sewn

The sewing of the car is over.

Fold the sewing edge on one side with an iron, 0.5cm.

边处理常用的7种缝制方法精讲

The same way is the same.

边处理常用的7种缝制方法精讲

Then press the thread in the folding place.

Spread the sewing.

边处理常用的7种缝制方法精讲

Set up to one side. Here is about 0.6cm of sewing. So you must first judge where to pour it, so that you will be sure which side is cut off.

Use the sewing of the other side to wrap the cutting side of the cutting side. Iron

边处理常用的7种缝制方法精讲

Press the thread at the fold.

边处理常用的7种缝制方法精讲

Press, fall to one side to the side, cover the side of the cloth edge.

This is much more reliable than the edge.

边处理常用的7种缝制方法精讲

Border gap

The stitching edge can be seen that some of your casual clothing films are one -sided, and there is a bright line parallel to the gap on the front.

After the sewing of the car is completed, the sewing is performed aside. Perform the vehicle sewing line on the front. The lower needle distance is 0.5cm. Of course, if you are skilled, you can not iron, and separate with your hands slightly. Complete the car seam evenly. The front picture is as follows:

边处理常用的7种缝制方法精讲

Complete the picture on the opposite side. Because it is flatter than the offline, we have to turn to the front car seam instead of directly on the back of the car.

边处理常用的7种缝制方法精讲

This kind of edge sewing is applied to the cloth after the lock edge. (Since it is a sewing to one side, just lock the edges together.)

If there is no sewing machine. We use the following two types of edging techniques. Thin cloth

Two times the stitching standards are reserved when cutting the cloth. After the sewing of the car is completed, then one of the sewing (one side of the direction to the direction) is subtracted by half, which is trimmed into a guaranteed size.

边处理常用的7种缝制方法精讲

Wrap it with the seams on the other side. (Step is the same as the seam of the edge.)

Fall the processed sewing to the side.

边处理常用的7种缝制方法精讲

Turn to the front for the pressure line.

边处理常用的7种缝制方法精讲

The negative effect.

边处理常用的7种缝制方法精讲

Thick fabric

Thick cloth cannot be stacked so many layers like thin fabrics. Pour a sewing of one -third of the sewing. Another fabric can perform simple lock (sewing machine or hand sewing).

Go back to the front and press the stitches between the two seams.

The negative effect. (There is no processing on the side in the figure below. It is recommended to lock the edge simply.)

边处理常用的7种缝制方法精讲

Dual -line pressure line

边处理常用的7种缝制方法精讲

Sometimes some clothes are pressed on the double Ming line. One situation is the five -line stretch (such as the T -shirt cuffs and hem), and the other is to perform the twin -line pressure line (more common in denim in denim) after sewing. There is a bright line on the surface after the stitch. Another bright line in the position of the seams becomes a double line. There will be a two -needle with a sewing machine with all functions, and one can be added with a wire shaft. This can be pressed out of the dual -line sewing. Industrial production must do this for efficiency. However, if the sewing machine does not have a dual -line function, it has to be sewn twice. Fortunately, if you have a reference first, it is not cumbersome to sew a parallel line. Positive effect

The negative effect. (The method of thin fabrics is used here.)

Bilateral folding

边处理常用的7种缝制方法精讲

What is the seam of the bread on it is that the sewing part is falling to the light line, and the bilateral seams mentioned next are splitting the seam and then pressing the line.

边处理常用的7种缝制方法精讲

After the sewing of the car is completed, the sewing is folded and ironed, the direction is the back, and the size of the size is half a seam. Then split the sewing.

边处理常用的7种缝制方法精讲

Turn to the front of the car, just like all the distance between turning back to the front pressure line. Try to get closer to the edge of the seam under the cloth at this time, but be sure to sew it to the sewing. Positive effect

边处理常用的7种缝制方法精讲

Next, let’s distinguish between the bright line and there is no obvious difference. The side treatment mentioned here is divided into two types: bright line and no bright line, or there is a bright line that is not in the front process that there is no bright line. So where is the difference between not pressing the line. First of all, it is a decorative effect. The light line is also regarded as a decoration, especially for some clothes with large color differences to make bright lines. Can be used as a emphasis on the structure of the clothes, a sense of mechanical? Modern sense? If you do fashion comments in the future, you can basically pull these directions. And our traditional formal dress emphasizes the hiding of the lines, so the clothes look integrated and look tall. Secondly, the bright line strengthened the degree of strong. Especially after the sewing is falling to one side, the light line is added, so a large part of the external forces that the stitching line is assigned by the light line is shared by the bright line. So the clothes became stronger. This is why almost all the sewing of the workmanship must be on the bright line, even the dual -bright line. Finally, the bright line makes the clothes more stiff. You can touch the bright line of the denim jacket or jeans, is it very hard, similar to the wire in the tight corset. The structure on the structure of the structure seems to have a shelf supporting the whole clothes. Let me talk about my appropriate understanding of clothing. In my opinion, clothing is two types: structure and deconstruction. To put it plainly, it is a sense of fit and a strong sense. The structure of any clothes is nothing more than these two or these two combinations. From this perspective, we look at the production of the entire clothing. From the fabric, we can distribute the soft and stiff. When designing and making a version, it can be divided into a three -dimensional shape that fit the human body. In terms of process, it can be divided into a sense of fit (the piercing line is a means, and the lining is also one, of course, and other). When designing this way, there will be a smooth idea. For example Essence In many of our low -grade clothing now, we can’t see this logic, and the level of designers is self -evident.

Stitch

边处理常用的7种缝制方法精讲

The name of the bag seam is very vivid, just like putting the edge into a small bag. This processing is suitable for thin cloth. Everyone must always encounter thin cloth clothes and damage to the cloth stitching thread directly. Because basically the factory will not give you such a strong craft. The first is to save costs. Secondly, it is not bad to wear a piece of clothes for 10080 years. What they eat. Pay attention to the reservation of the sewing. See the figure below for details.

边处理常用的7种缝制方法精讲

The sewing positioning is 1.2cm, but the current car is sewn at a position of 0.5cm from edge. Then completely split the sewing. The thoroughness to be split (but not for you, the thin cloth is very fragile.) The more important point is: the back of the fabric should be opposed to the car seam. (Generally, the sewing is opposite, and the sewing portions are in the opposite side. Here is to be reversed.)

边处理常用的7种缝制方法精讲

Then let the front fold the front and wrap the sewing.

边处理常用的7种缝制方法精讲

The effect after completion.

边处理常用的7种缝制方法精讲

Then the previously setting line seam, which is 0.7cm from the current edge.

边处理常用的7种缝制方法精讲

After the completion, the sewing reached the back and was wrapped.

But every step must be trimmed. Otherwise, there will be many silk threads in the end, which is more troublesome to trim. As shown below.

Wanshui and thousands of mountains are always affectionate.

The negative effect.

Product Recommendation: single needle cylinder basting machine