How long does it take to change the sawbone?

0 Comments

I often hear some users complaining: “Why did the sawing grinds of our family webbone break it in a few days!”, And even some users used a few worst saws a day! The opposite is that some other users will not have a sawdust in a few months.

The contrast is so big, what is going on?

锯骨机的锯条多久换一次

In fact, this is a comprehensive problem. There are many factors that affect the life of the sawbi. It cannot be simply collected to the quality and bad quality of the sawbag.

L

Saw strip material

Food blisters are generally used to see pork bones, pork ribs, sheep bones, beef pork, ox tails, frozen meat, frozen fish, etc. It is widely used in large and medium -sized food processing plants, slaughterhouses, meat connection factories, supermarkets and other places. Therefore, the turbone sawing clindless to the food must use high -quality “food -grade stainless steel”. 4 teeth and 6 teeth are commonly used in the turbone. The hardness of the root saws is different. Choose different number of teeth, otherwise it will also affect the life of the sawbag.

Hua Lingxi Kitchen’s Blatch is imported from Sweden. The amount of meat dandruff is produced during work, and the tensile strength of the sawbag is high, thereby increasing the service life. For the different cut ingredients, three different saws are introduced: 3P sawdr saw jelly fish, 4P sawdr saw jelly meat, and 6P sawdr sawing bone. ((

There are 3 teeth in 1 inch, which are sawn frozen fish. There are 4 teeth in 1 inch. It is a sawdown. 1 inch is 5 teeth. )

锯骨机的锯条多久换一次

Saw strip length

The length of the sawbring should not affect the life of the sawpin, but the bloggers need to be tightly sawed. Due to its structural reasons, the changes in the length of the sawbar will cause changes in tension and affect the service life of the sawbi.

锯骨机的锯条多久换一次

Hua Ling’s aluminum -magnesium alloy barking machine is polished by robotics and all of them are oxidized. There are two desktop models: 1650A and 1900A. Hua Ling’s stainless steel turbone has 1650 desktop types, and 2020 and 2400 landing types.

锯骨机的锯条多久换一次

According to the model of the turbone machine, Hua Ling is equipped with a sawdust of the length, and it must not be used privately.

锯骨机的锯条多久换一次

How to change the saw chief correctly

锯骨机的锯条多久换一次

When reinstalling the sawd, just loosen the rotating valve or knob above to the right position (from the above machine, it is

锯骨机的锯条多久换一次

Adverse hour hand) Smaller the active wheels and the distance from before the wheels, and the saw blades are easily removed. Then change to a new sawer. At this time, pay attention to the direction of the sawing side, otherwise it will loosen and fall off. It is necessary to ensure that the saw blade is properly installed between scraping, top pulley, bottom pulley, and central disk, and can just pass through the middle -oriented groove. In order to ensure that the machine runs normally, it is necessary to ensure that the saw blade is indeed running on the pulley. In the correct state, the edge of the saw Chifeng should be straight with the front edge of the pulley. If it is not a straight line, it must be adjusted to ensure that the sawdles do not run inward or outward.

The frequency of a good quality turbiar, the frequency of its sawbi replacement is relatively lower. When buying a blister, don’t just look at the price. Although the cost of buying a blogging machine is a little lower, the cutting efficiency in the process of use is low, the waste of meat dandruff, and the cost of buying a saw clipper.

Hua Lingxi Kitchen focuses on the research and development and production of food machinery and commercial kitchenware, and has cultivated a professional after -sales service team to provide you with one -stop pre -sales and after -sales after -sales. Some quality.

L